Sccm Task Sequence Not Continuing After Reboot

In the Configuration Manager console, go to the Software Library workspace, expand Operating Systems, and then select the Task Sequences node. Issue: When trying to perform an OSD Task Sequence using SCCM 2007, the deployment fails, usually after it has successfully formatted the drive, dropped the image on the PC, and scanned for drivers. This is not to panic the customers when they see the reboot prompt, and they know it's something officially done on their system. SCCM 2012 SP1 – Enable Command Support Console in WinPE January 6, 2014 / [email protected] How to restart the task sequence wizard in WINPE without having to reboot If you make a mistake and cancel out the task sequence wizard in WinPE you can restart it without rebooting. 1 Enterprise , the task sequence works perfectly fine but when we run the same task on HP Elite 8300 system having Intel 82579LM Adapter from Windows XP , after the reboot the. If a task sequence is not continuing after the Install update step it is probably due to component based servicing. Unfortunately, this also applies when the TS fails. cmd is a custom script that runs during or after the Windows Setup process. Configuration Manager 2012 OSD Fails After Restart 28th January 2014 richardjgreen I was working today testing the operating system deployment capability of System Center Configuration Manager 2012 (not R2) for a Windows 7 task sequence. get-service not recognised after task sequence restart We have a task sequence to update a few applications and install most recent monthly update rollup on our Win 7x64 SP1 endpoints. Lately one of my Windows 10 machines started to behave quite strange, after about a day of use, browsing Internet was no longer possible. Fatal error is returned in check for reboot request of the action (Restart Computer). Task sequence cannot continue after reboot because TS Manager is not configured to auto-start or GINA is not installed. I've been struggling to get ThinInstaller working properly with SCCM operating system deploy task sequence. Unfortunately it is not as user friendly as we would like, most notably there is no warning to the user that an upgrade is about to take place (when you set the upgrade task sequence to required). Error: Task sequence cannot continue after reboot because TS Manager is not configured to auto-start or GINA is not installed The Restart Computer action cannot be used to boot into a newly deployed operating system (or used to boot into the Full OS if a task sequence was started from WinPE) because the OS has not been configured to resume the task sequence. Hello Everyone! I'm trying to deploy Windows 7 Image via SCCM 2012 but i'm facing the following issue. Fixes a problem in which multiple applications in a dependency chain may not install after a computer restart in System Center Configuration Manager. 24, I believe). SCCM runs as the local system account whereas MDT runs as local admin. Prepare for Upgrade is the first stage where it will analyse the machine whether it's eligible to Windows 10 1709 upgrade. The PXE boot is working properly but after that it is not installing the Windows the computer is restarting itself before the Windows 7 image installation begins. Is there a way to disable this at the task sequence level? I don't want to set every step to 'continue on error' either. This documentation doesn’t mention it, but because Configuration Manager Applications must not initiate a reboot, I’m going to add the SETUP_REBOOT property with a value of “Never” in order to be certain that the uninstallation process will not restart the computer unexpectedly. In my OSD Task Sequence, I put a reboot after this step so the agent runs with the new settings. After the reboot it boots into Windows logon screen and goes no further. Postpone a forced Software Center reboot (SCCM 2012) by Ryan Carroll • September 10, 2013 • Articles • 24 Comments In our environment, we have SCCM configured to force a restart after updates. My sequence towards the end is: add to domain, restart, install Sophos, enable BitLocker, restart. 11170 11 Failed The task sequence manager could not successfully complete execution of the task sequence needed for installation to continue 11270 102 Reboot. In the example, the first step that runs sets that "WindowsVersion" task sequence variable, and the rest of the step groups will only run if the current version does not match the version number you set in the step conditions. If you run Lenovo Thinstaller via Configuration Manager task sequence , you cannot run the installation program, because it is a. It has been working fine up till now. I get the following: failed to reboot the machine because the service window is not available. Ever tried to do an OSD with System Center Configuration Manager 2007 and have it fail "Task sequence cannot continue after reboot because TS Manager is not configured to auto-start or GINA is not installed?" If so then check out this tip from Frank Rojas on why this may happen and how you can fix it: =====. Right-click on the task sequence and click Deploy. Keep in mind that even if PXE is first in the boot order, the computer does not actually boot to PXE unless Configuration Manager has a task sequence for it to run. So for my task sequence Beta I have the same boot wim assigned to it as was uploaded to the wds server, no big deal. We only deploy OSD TS's to a specific collection, and have a password in front of it. If you have started a task sequence in Configuration Manager and you hit a problem, the last thing you want to do is to have to go through the reboot process back into Windows PE. I can not recommend a particular place to inject it as I have no idea of what is responsible of this registry change. Is there a way to display the rest of the Task Sequence please? If there is a problem its much easier to troubleshoot. Sample screenshot:. Modify the Task Sequence. I've been struggling to get ThinInstaller working properly with SCCM operating system deploy task sequence. Configuration Manager 2007 does not allow a task sequence to reboot back to PXE. When SetupComplete. " I just wanted to ask if there is any variable that I can add to TS to continue the TS after reboot? Please share your thoughts and thank you for your time and help. You'll have to toss it into a package to serve up to the task sequence of course. Restart SCCM OSD Task Sequence within Windows PE - If you want to restart SCCM OSD Task Sequence from within Windows PE without having to reboot the machine and start the PXE boot sequence again, you can qu - Restart SCCM OSD Task Sequence. That means that this action is not part of the task sequence progress and by that not monitored. Unfortunately, it does this on its own and before the task sequence begins. Most cases I see are hung after the image is down on the machine and waiting for the applications to load. This allow us to continue the task sequence after the restart, and not have to perform any potentially unsupported modification of built-in task sequence variables or re-starting the sequence all over (like I did in my previous custom solution). Unfortunately it is not as user friendly as we would like, most notably there is no warning to the user that an upgrade is about to take place (when you set the upgrade task sequence to required). Task Sequence and shutdown (not reboot) a computer and continue For some reason there is a requirement to do a computer shutdown (not restart) while running a task sequence, and once the computer starts again there is a need to continue running the task sequence where we left it. If you don't sign in after one hour to continue debugging, the task sequence fails. This works in part, the task sequence now doesn't automatically reboot, it moves on to the restart computer step, so you are presented with the 2 hour warning. So for my task sequence Beta I have the same boot wim assigned to it as was uploaded to the wds server, no big deal. Choose Required as the purpose and make the advertisement available only to Configuration Manager clients. LOG after Restart Computer step in an in place upgrade task sequence (SCCM 1806 CB) Posted on September 1, 2018 by ncbrady I noticed that my in place upgrade task sequence (Windows 10 1709) was failing after the built in Restart Computer step, just bombing out of the task sequence. The second restart is not controlled by the Task Sequence engine and causes the engine to be unable to resume the Task Sequence when the computer comes back up after the second restart. Deployment took an extra restart after selecting which task sequence to use. SCCM 2012 SP1 MDT task sequence fails on reboot does not retain ip we are having a sccm 2012 sp1 server that used for installation of win 8. That means that this action is not part of the task sequence progress and by that not monitored. I have a OSD task sequence that does install ConfigMgr and does not continue after the "Setup Windows and ConfigMgr" step. There are well known methods to force an advertisement to rerun – including several add-on tools available for the SMS or SCCM console. After making the change to the deployment settings to be "Configuration Manager Clients, media, and PXE", the final status message at end of task history report is now "Program received". Note: Jonathan Conway has a great blog on how to use Manage-bde with the Task Sequence called SCCM Windows 10 Upgrade Task Sequence: BitLocker PIN Protector Issues on Laptops. inf file to use - Depending on the sysprep. We have a custom task sequence and we noticed that software deployment are messed up due to. Alternatively. If this task sequence. You can easily find it by searching this text in the relevent log. It will create a scheduled task that runs specified SCCM Client Policy requests at whatever interval you want for as long as you want. Keep in mind this won't work everytime as it depends on where you failed your task sequence. This documentation doesn’t mention it, but because Configuration Manager Applications must not initiate a reboot, I’m going to add the SETUP_REBOOT property with a value of “Never” in order to be certain that the uninstallation process will not restart the computer unexpectedly. log file when you experience this issue:. SCCM 2012 SP1 MDT task sequence fails on reboot does not retain ip we are having a sccm 2012 sp1 server that used for installation of win 8. After the step "Setup Windows and ConfigMgr" the computer reboots and displays a blue screen with "Just a moment" in the background the TS is running but we can't see it. This can be useful if you have several reboots during a Task Sequence and you need to make sure that BitLocker stays suspended (optional method listed below). I didn't quite include all the of schedule types because. It's now possible to set the information in the Task Sequence Properties. Yes: Yes: SMSTSRetryRequested: Built in: Requests a retry after the current task sequence step is completed. I had a very unusual issue come up where a task sequence continuously failed right after WinPE booted. Then add a Run Command Line Task to the TS. After double checking my work, I found the problem was that I had enabled my Task Sequence Media for unattended installs and I had not deployed my task sequence as a mandatory deployment. Monitor SCCM Task Sequence Using the Console. You can tell it will copy down the boot image because SCCM will ask you to reboot before running the actual task sequence. I was working today testing the operating system deployment capability of System Center Configuration Manager 2012 (not R2) for a Windows 7 task sequence. A reboot fixed the problem, and then after about a day, sometimes less, the same thing happened. We're deploying windows 7 using sccm R2. After double checking my work, I found the problem was that I had enabled my Task Sequence Media for unattended installs and I had not deployed my task sequence as a mandatory deployment. Deploy this task sequence the same way that you would do any other deployment. Setup windows and Configuration Manager task should never be disabled. This series will be focusing on ConfigMgr 2012, and helping you get the best out of the product using features you may have not looked at in ConfigMgr 2007 or features which are new in ConfigMgr 2012. To combat this problem, I implemented the following solution from Steve Rachui , which moves the TS logs to a network share for proper archiving and ease of access. 0 or USB-C dongles to lock up or lose connection. At some point after the "Setup Windows and ConfigMgr" task, a power failure or crash occurs on the PC. This will run the PowerShell command after the Task Sequence ends. That should not be the case if the task sequence is configured correctly. cmd is a custom script that runs during or after the Windows Setup process. In my OSD Task Sequence, I put a reboot after this step so the agent runs with the new settings. Thank you for this! Our SCCM stopped showing task sequences when we tried to clone (PXE or Media boot). Is there a way to make it continue the task sequence after it reboots without trying to restart it while leaving the usb stick (allowing it to be totally unattended)? Otherwise, someone has to time pulling the usb stick each time this tries to reboot, and then stick it back in. cmd is disabled, the task sequence can't continue after Windows Setup finishes. Note: Throughout this post I’m just going to refer to “ConfigMgr 2012 R2 SP1” but note that this actually applies to both System Center 2012 R2 Configuration SP1 and System Center 2012 Configuration Manager SP2. The task sequence we are creating will only contain one SCCM package (in some situations you may need to add more than one package). First I suspected an issue within the boot images (not deployed correctly?). This documentation doesn’t mention it, but because Configuration Manager Applications must not initiate a reboot, I’m going to add the SETUP_REBOOT property with a value of “Never” in order to be certain that the uninstallation process will not restart the computer unexpectedly. Deploying BIOS updates during SCCM Task Sequence or Advertised Program May 6, 2011 Matthew C. So I change the "user experience" to "The software install program might force a device restart" and am still not having success. Eventually, after a very long a tedious group policy stripping process, the issue turned out to be the "dmwappushservice" being set to Disabled. The deployment verification settings are based on the current membership of the collection. Run a hidden/published SCCM task sequence based on conditions using the below command. Now, to disable BitLocker, you could place that step in the Task Sequence and allow it to 'Continue on error'. However, after the Setup Windows and ConfigMgr step, the machine will reboot, and you can use this reboot to install packages and also run command line steps. Now, to disable BitLocker, you could place that step in the Task Sequence and allow it to ‘Continue on error’. Previously, the SCCM client would start talking to the MP and everything was good to go (except one small clean up step). Allow the user to postpone the installation/upgrade of an application x amount of times. I experienced an unexpected restart during a build and capture of Windows 10 with the 'install Updates' task sequence step and the latest Windows 10 updates deployed to the referenced image. 1 Answer 1 1 The restart computer task sequence step will only continue the task sequence if you boot back into the boot media, says their documentation. The Re-run Task Sequence Tool has the same effect 🙁 Any ideas what goes wrong?. Stage 1 will be built in a remote location (warehouse) using an USB key and Stage 2 will be on the client network. The complete variables used and accessible by SCCM during the task sequence can be found here: SCCM 2012 and above click here; SCCM 2007 click here. So we want to use a SCCM task sequence to disable the UWF, reboot, perform the application steps, enable the UWF, reboot. Clients do not automatically wake using the wake on LAN feature when deadlines for mandatory software distribution, software update, or task sequence deployments are reached. I have created some tables below of the variables, which are a little easier to filter, sort and generally find the variable you are after. net framework 4. Open your task sequence and before the Sysprep and capture step, something like this works fine. However, this is a build (& capture) technique. It's now possible to set the information in the Task Sequence Properties. Recently, while developing a solution for a Windows 10 servicing project I needed a solution to rerun a task sequence at a given time. A customer of mine had an incident where the TS hung because Hotfix KB2761938 wasn’t installed on the clients. Configuration Manager 2007 does not allow a task sequence to reboot back to PXE. _SMSTSMachineName –> The machine name of the computer where the task sequence is currently executed on. There was a question asked on the forum on how to add a "true" restart in the end of a task sequence, which normally would have broken the task sequence, in ConfigMgr 2012 SP1 there is a new Task Sequence variable called SMSTSPostaction. I had a very unusual issue come up where a task sequence continuously failed right after WinPE booted. Because this second restart is not controlled by the task sequence, no execution state is saved before the restart. After update install, the task sequence has a restart step, after the restart we have the following 3 steps:. Note: Throughout this post I’m just going to refer to “ConfigMgr 2012 R2 SP1” but note that this actually applies to both System Center 2012 R2 Configuration SP1 and System Center 2012 Configuration Manager SP2. However, after the Setup Windows and ConfigMgr step, the machine will reboot, and you can use this reboot to install packages and also run command line steps. No boot device is available and if you PXE again it starts over. Additionally, the following message may be logged to the Smsts. We only deploy OSD TS's to a specific collection, and have a password in front of it. Microsoft thoughtfully added “testing only” to remind you to turn the feature off when your task-sequence (TS) is ready for production. I did the exact same update, but did not push with group policy, I just pushed the package as an app in the background, and did not force the restart. Simply add a Set Task Sequence Variable step before or after any step you want to change the dialog display for, then set the value to True or False depending on the desired display mode. Eventually, after a very long a tedious group policy stripping process, the issue turned out to be the "dmwappushservice" being set to Disabled. Modify the Task Sequence. You can use it anywhere in your Task Sequence to toggle the dialog on or off. Hi guys, i'm faced with a strange problem at the moment. Under OSD, you will see a TS section. ConfigMgr 101: Maintenance Windows Welcome to ConfigMgr 101. log command prompt F8 OSD SCCM SMSTS. Occasional failure to install applications during task sequence I'm looking for some hints if anyone has come across this. Go to Software Library / Operating Systems / Task Sequences; Right-Click your task sequence, select Properties. I do have my packages set to install outside the maintainace window. Hello Everyone! I'm trying to deploy Windows 7 Image via SCCM 2012 but i'm facing the following issue. In my environment this message would usually last 2 - 5 minutes each restart. This issue occurs after you change an existing task sequence in the task sequence editor to add Install Package actions. I did the exact same update, but did not push with group policy, I just pushed the package as an app in the background, and did not force the restart. Restart SCCM OSD Task Sequence within Windows PE - If you want to restart SCCM OSD Task Sequence from within Windows PE without having to reboot the machine and start the PXE boot sequence again, you can qu - Restart SCCM OSD Task Sequence. For example, a Package will perform differently when deployed in a Task Sequence than when it is deployed directly to a collection. msu /quiet /norestart. Countdown timer. In SCCM image deployment if you get the below error during software/application installation, it could be a problem with restart step in task sequence To confirm this you have to check the deployment log and you will be getting the below error after the restart step, The operating system reported error 50: The request is not supported. This task sequence variable can be used to configure a post action for a task sequence. There was a question asked on the forum on how to add a "true" restart in the end of a task sequence, which normally would have broken the task sequence, in ConfigMgr 2012 SP1 there is a new Task Sequence variable called SMSTSPostaction. To function correctly, open each task sequence action that uses a custom action in an editor. After installing OS, the system restarts and sits in the login screen. Enabling BitLocker in SCCM Task Sequence. Clients do not automatically wake using the wake on LAN feature when deadlines for mandatory software distribution, software update, or task sequence deployments are reached. There are 5 groups in Windows 10 Enterprise 1709 Upgrade task sequence. This is another new task sequence variable in ConfigMgr 2012 SP1, which is currently still in BETA, named SMSTSPostAction. This is the moment where “SMSTSPostAction” comes in place. Is there a way to disable this at the task sequence level? I don't want to set every step to 'continue on error' either. 19 thoughts on " Task Sequence stuck 'Installing' in sequence-stuck-installing-in-software-center Task sequence correctly, exit it and continue. I have a OSD task sequence that does install ConfigMgr and does not continue after the "Setup Windows and ConfigMgr" step. Do you put this pause before or after the application task? I ask because I've just added a task to add Sophos and I have problems. The latest version of SCCM is version 1902. Thank you for this! Our SCCM stopped showing task sequences when we tried to clone (PXE or Media boot). 1 Enterprise , the task sequence works perfectly fine but when we run the same task on HP Elite 8300 system having Intel 82579LM Adapter from Windows XP , after the reboot the. This post will explain the different Program configuration options and deployment types and detail the resulting reboot behaviour for all the various combinations. inf file to use - Depending on the sysprep. You can easily find it by searching this text in the relevent log. We have a custom task sequence and we noticed that software deployment are messed up due to. This session focuses on the task sequence. We are driven down a more logic-aware route to perform tasks in a sequence. I’ve not checked too intensely but I’m not sure if there is any way to change this setting, except to suppress the 3010 code in a script and do a controlled reboot using the Restart Computer task sequence step, mentioned below. msu file) to an image right after deployment. A task sequence automatically picks up the operating system image when you select Do not select now during the task sequence creation. SCCM 2012 SP1 MDT task sequence fails on reboot does not retain ip we are having a sccm 2012 sp1 server that used for installation of win 8. A resource for troubleshooting System Center Configuration Manager (Current Branch) and System Center 2012 Configuration Manager Task Sequence failures through analysis of errors reported in the smsts. To add individual tasks into the task sequence: Right-click in the newly created task sequence. Microsoft thoughtfully added “testing only” to remind you to turn the feature off when your task-sequence (TS) is ready for production. Using Configuration Manager console, you can now identify client devices that require a restart. What’s changed ConfigMgr 2012 R2 SP1 is the minimum version we support for Windows 10 in-place upgrade using this sample content. The issue started after the upgrade. This is session three of a series that details the Operating System Deployment feature of Configuration Manager. For example, a Package will perform differently when deployed in a Task Sequence than when it is deployed directly to a collection. cmd is a custom script that runs during or after the Windows Setup process. com The restart computer task sequence step will only continue the task sequence if you boot back into the boot media, says their documentation. Keep in mind this won't work everytime as it depends on where you failed your task sequence. Previously, the SCCM client would start talking to the MP and everything was good to go (except one small clean up step). In short, the problem was that my clients would boot into Windows PE (WinPE), but would not begin their advertised task sequence. My current setup works like this: Package created with the unpacked contents of lenovothininstaller1. Sample screenshot:. The "restart computer the boot image assigned to this task sequence" step doesn't work for some reason as soon as the PC restarts it doesn't resume where it left off within the Task sequence it starts looking for an Operating System instead of continuing with the task sequence. Because this second restart is not controlled by the task sequence, no execution state is saved before the restart. The main idea is to initiate an SCCM reboot with a long enough countdown and in parallel, to fire a command line shutdown to switch the PC off. Stackoverflow. Clients do not automatically wake using the wake on LAN feature when deadlines for mandatory software distribution, software update, or task sequence deployments are reached. When SetupComplete. Each of them has their own benefits and drawbacks. Pingback: SCCM: install Windows 10 language packs offline with an MDT Integrated Task Sequence in SCCM CB | IT Consultant Everyday Notes. This causes the task sequence to prematurely end. Purely to provide the technical answer. After update install, the task sequence has a restart step, after the restart we have the following 3 steps:. Restart in Windows PE: Use this task sequence step to specify the restart options for the destination computer that receives this task sequence. Use the SCCM Task Sequence Debugger. I’m relatively new to running SCCM in Native Mode, and the other day I came across an issue I hadn’t seen before. Simply add a Set Task Sequence Variable step before or after any step you want to change the dialog display for, then set the value to True or False depending on the desired display mode. If not, it is a good idea to do so anyway as a lot of changes were just made to your Configuration Manager environment. exe Windows6. After update install, the task sequence has a restart step, after the restart we have the following 3 steps:. It fails when enabling BitLocker. Prevent that and any delays from any reboot during the task sequence by setting SMSTSRebootDelay to 0 (zero). It has been working fine up till now. A customer of ours is attempting to update the BIOS as a step in a SCCM 2012 task sequence. Now, to disable BitLocker, you could place that step in the Task Sequence and allow it to 'Continue on error'. to go ahead and restart the task sequence completely. Typically, a Boot Image is not assigned to an In-place Upgrade Task Sequence. There are 5 groups in Windows 10 Enterprise 1709 Upgrade task sequence. When Task sequences won't show up in SCCM Software Center check if you have the lowest session ID when multiple sessions exist! Problem I recently ran into the problem that the task sequence I wanted to test won't show up in the SCCM Software Center. But to be really safe, place your command just before the failing reboot. You can advertise a task sequence just like you can advertise any other program. Simply add a Set Task Sequence Variable step before or after any step you want to change the dialog display for, then set the value to True or False depending on the desired display mode. For example, let's say you set Default size to 100 and the Maximum size to 1000. It contains commands to restart the Configuration Manager task sequence after Windows Setup finishes. We would like to install. I've recently been looking at using SCCM Windows Upgrade Task Sequences to migrate from Windows 10 1511 to Windows 10 1607 for a customer. So out-of-the box SCCM traffic goes unencrypted via HTTP, which is clear text. There are well known methods to force an advertisement to rerun – including several add-on tools available for the SMS or SCCM console. It must not initiate a restart on its own. To update the computer BIOS after initial deployment you need to create a new SCCM Collection. Setup windows and Configuration Manager task should never be disabled. Now, to disable BitLocker, you could place that step in the Task Sequence and allow it to 'Continue on error'. It gets as far as "Setup Windows and ConfigMngr" where it will reboot. Skipping Task Sequence because it’s not active yet Date: June 24, 2015 Author: SCCMentor 20 Comments Whilst trying to rebuild a device via OSD I noticed that the advertised Task Sequence was not showing up my list of available Task Sequences. Part of this may be because task sequences are typically thought of as focused on Operating System. To resolve this issue, we recommend that you apply any updates that require dual restarts by using the usual Software Updates feature of Configuration Manager instead of using task sequences. In short the following updates are affecting your OSD Task Sequence:. 2 on HP machines in SCCM OSD Task Sequence. If the reboot occurs due to the use of the Restart Computer task sequence step, you are able to specify exactly. In some cases it comes in handy to restart or shutdown your task sequence (TS) at the end of the TS. Configuration Manager 2012 OSD Fails After Restart 28th January 2014 richardjgreen I was working today testing the operating system deployment capability of System Center Configuration Manager 2012 (not R2) for a Windows 7 task sequence. You can tell it will copy down the boot image because SCCM will ask you to reboot before running the actual task sequence. If the user postpones the installation the script will return exit code 1 and SCCM will assume it failed and not continue depending program or task sequence. Our post will shows 4 different ways to monitor SCCM task sequences. Do you put this pause before or after the application task? I ask because I've just added a task to add Sophos and I have problems. Unfortunately it is not as user friendly as we would like, most notably there is no warning to the user that an upgrade is about to take place (when you set the upgrade task sequence to required). Recently, while developing a solution for a Windows 10 servicing project I needed a solution to rerun a task sequence at a given time. I experienced an unexpected restart during a build and capture of Windows 10 with the 'install Updates' task sequence step and the latest Windows 10 updates deployed to the referenced image. Whenever I look at your web site in Safari, it looks fine however, when opening in IE, it’s got some overlapping issues. Unfortunately it is not as user friendly as we would like, most notably there is no warning to the user that an upgrade is about to take place (when you set the upgrade task sequence to required). RE: [MDT-OSD] Task Sequence not continuing after first reboot Michael Niehaus Mon, 23 Jun 2014 18:19:24 -0700 Are you applying a policy that enables UAC for the built-in Administrator account (or otherwise modifying MDT to run under an account that uses UAC)?. GP processing is disabled during SCCM's build so you need a final reboot to get it to pick up the changes. get-service not recognised after task sequence restart We have a task sequence to update a few applications and install most recent monthly update rollup on our Win 7x64 SP1 endpoints. Modify the Task Sequence. I've tested this now a numerous times and it works like a charm, just keep in mind that it's triggered after the task sequence is started. This causes the task sequence to prematurely end. SMSTSRetryRequested: Requests a retry after the current task sequence step is completed. The Install software packages according to dynamic variable list option is automatically selected. Sample screenshot:. System is halted”. After you deploy the task sequence, Configuration Manager doesn't reevaluate the collection membership for the high-risk deployment settings. net framework 4 during the osd, then, a task sequence to reboot, and then, continue to install other softwares. Click Next on the Configuration Manager Setup Wizard Welcome. After creating the Diskpart configuration file, it then runs Diskpart referencing the configuration file in order to create suitably-sized/lettered partitions to successfully boot from using UEFI and that are also accessible for the Task Sequence to download and pre-stage the latest Boot Image if it’s required (i. One thing to take into account is the fact that the seperate programs you run in a task sequence cannot allow user interaction, or they will not be selectable for. I've not checked too intensely but I'm not sure if there is any way to change this setting, except to suppress the 3010 code in a script and do a controlled reboot using the Restart Computer task sequence step, mentioned below. Fix Windows 10 In-Place Upgrade Task Sequence infinity restart loop We successfully did Windows 10 In-Place Upgrade for hundreds machines, but few of them went into infinity restart loop at the end. 11170 11 Failed The task sequence manager could not successfully complete execution of the task sequence needed for installation to continue 11270 102 Reboot. SetupComplete. The "restart computer the boot image assigned to this task sequence" step doesn't work for some reason as soon as the PC restarts it doesn't resume where it left off within the Task sequence it starts looking for an Operating System instead of continuing with the task sequence. I'm working with SCCM. Command Line to Trigger SCCM Task Sequence. This update applies to Microsoft System Center 2012 R2 Configuration Manager Service Pack 1 and Microsoft System Center 2012. OS|DC: MDT 8443: Task Sequence stops after reboot. After digging through all of the usual logs and performing all of the tests to attempt to identify the issue, I came across an old blog post about applications, but not packages appearing in the Software Center in Configuration Manager 2012. I have a OSD task sequence that does install ConfigMgr and does not continue after the "Setup Windows and ConfigMgr" step. When an SCCM task sequence fails, errors are written to the smsts. You can view the progress of a task sequence using the SCCM console. Add a new group before the Install Operating System section; In the Option tab, set the condition for task sequence variable _SMSTSBootUEFI not equals true. MDT basically tries to start where it leaves off and fail. NET executable and the default policy is to disallow running it from a network share or distribution point. Run a hidden/published SCCM task sequence based on conditions using the below command. Ever tried to do an OSD with System Center Configuration Manager 2007 and have it fail "Task sequence cannot continue after reboot because TS Manager is not configured to auto-start or GINA is not installed?" If so then check out this tip from Frank Rojas on why this may happen and how you can fix it: =====. I've been struggling to get ThinInstaller working properly with SCCM operating system deploy task sequence. SCCM 2012 continues installing the next application in order (unsuccessfully) when 3010 is returned. First, let’s explain how it works. Once deployed on the client. SCCM 2012 - How to catch errors in Task Sequence Issue Description: A key requirement with a task sequence is to intelligently capture logs in case of a failure or a success. First I suspected an issue within the boot images (not deployed correctly?). One thing to take into account is the fact that the seperate programs you run in a task sequence cannot allow user interaction, or they will not be selectable for. 1 Update, drivers, firmware, applications, and configurations to Surface Pro devices managed by using System Center R2 2012. MDT basically tries to start where it leaves off and fail. Part of this effort is to encrypt computers, especially laptops that leave the building. As far as I understand it, shutting down the PC during the reboot countdown will not break the task sequence and everything will continue peacefully at the next reboot. Not the Sophos task but the following task that enables BitLocker. You can advertise a task sequence just like you can advertise any other program. If a task sequence is not continuing after the Install update step it is probably due to component based servicing. However, after the Setup Windows and ConfigMgr step, the machine will reboot, and you can use this reboot to install packages and also run command line steps. exe) may consume 100 percent of the CPU. Peter van der Woude August 14, 2015 at 20:04. SCCM 2012 - Run action after Task Sequence is finished. SCCM comes with the ability to use BitLocker to encrypt during imaging. Removing the Task sequence ID works, but when i restart the service nothing happens and after a few seconds the Task Sequence ID is available again. set to “Continue on steps within your Task Sequence after you reboot into full. After checking around to make sure it wasn’t an SCCM infrastructure issue, I started looking at the laptop. wim) I tried adding duplicate steps in later in the sequence, after reboot. To add individual tasks into the task sequence: Right-click in the newly created task sequence. I was working today testing the operating system deployment capability of System Center Configuration Manager 2012 (not R2) for a Windows 7 task sequence. Step 2: Deploy the task sequence to your systems. O/S Deployment Thread, SCCM 2016 - Windows 10 OSD - Task Sequence - finishes with black screen & cursor in Technical; Hi All, I am getting a black screen with cursor after deploying Windows 10 OSD SCCM task sequence. So you can't see the Progress of the running TS or there is a TS running. A task sequence automatically picks up the operating system image when you select Do not select now during the task sequence creation. When you're working with ConfigMgr 2012 and task sequences, these tend to fail now and then. Remote Control During SCCM OSD (Without Modifying the Boot. I checked the task sequence itself to see if any reboot switches for any installs were in place - there weren't any. Step 3: Test application installation in a Task Sequence. Part of this may be because task sequences are typically thought of as focused on Operating System. Select Task Sequences in the menu in the left pane of the Configuration Manager console. The main idea is to initiate an SCCM reboot with a long enough countdown and in parallel, to fire a command line shutdown to switch the PC off. If you run Lenovo Thinstaller via Configuration Manager task sequence , you cannot run the installation program, because it is a. A supported hotfix is now available to address this issue. cmd is disabled, the task sequence can't continue after Windows Setup finishes. Restart SCCM OSD Task Sequence within Windows PE - If you want to restart SCCM OSD Task Sequence from within Windows PE without having to reboot the machine and start the PXE boot sequence again, you can qu - Restart SCCM OSD Task Sequence. Like last week I'm staying in the world of new features of Configuration Manager, version 1710. The PXE boot is working properly but after that it is not installing the Windows the computer is restarting itself before the Windows 7 image installation begins. We have a custom task sequence and we noticed that software deployment are messed up due to. If I add this as part of a Task Sequence (even as the only item) the PC will reboot. 1 Answer 1 1 The restart computer task sequence step will only continue the task sequence if you boot back into the boot media, says their documentation. Use that to deploy your WIM, and when you reboot, it will load into Windows PE – and then you can continue your advertised task sequence. Right-click on the task sequence and click Deploy. It needs to work with Dot. The Windows setup still initiates a few reboots and each is being count down from 15-20 seconds. It's always handy to have the option to pause a Task sequence for troubleshooting or testing. Setup windows and Configuration Manager task should never be disabled.